You can avoid all these problems by jumping on the issue as soon as you detect play between the pin and the bushing. To diagnose a worn hinge pin bushing, you 

4/13 · This video shows you how to install a new door hinge pin and bushings on your 1994-2004 Chevy S-10. Top 5 Problems 2000-06 GMC Yukon Sierra Chevy Suburban Tahoe Silverado Avalanche Cadillac Escalade This video covers the top problems you may find on

1:22. Use your screwdriver and pliers to remove the retainer located in the groove at the top of the hinge pin. step 2 :Remove spring. 1:50. Pull down with a screwdriver to pop it out. step 3 :Remove pins. 2:05. Use penetrating oil and use your screwdriver and your hammer to hammer out the pin.

Using our NAPA punch set, we selected a drift pin that fit the hinge pin and drove it up with a a few blows with a hammer. Be careful not to hit 

The lower bushing for the upper hinge pin was broken. I have plenty of experience replacing door hinge pins and bushings on several GM vehicles, especially B- 

Slide the door back toward the body of the car, and align the hinge halves. Install the new door hinge pin bushings into the holes of the hinge, and push the new pins through the hinge. Install the retaining clips to both door hinge pins. 1983-1993 Mustang Master Door Hinge Pin & Bushing Kit - by 5.0 Resto.

5/16 · Once all the new bushings are in and flush move the door hinge part back over and start your 2 bolts into the door finger tight. Then take your new pin and line everything up. Hammer the pin down flush so the "teeth" go into the hinge. Then align your door and tighten the 2 bolts on the door.!!

Have a helper remove the the door from body. With the door off everything can be easily accessed. Cut the hinge bolts in half with an ossilating cut off tool 

Steps to Replace Your Door Hinge Pin, Bushings and Spring · Remove the retainer clip on the top of the top hinge pin with a screwdriver and 

1A Auto shows you how to fix your sagging and sloppy door hinges on your 88 to 98 Chevy or GMC Silverado Sierra Pickup Truck and 92 to 99 Suburban, Yukon ,

Next, drive them out the rest of the way with a hammer and punch. Pull the door away enough to separate the hingle halves so you can access the bronze bushings.

Fleetline, Bel Air, 150 or 210's hinges back in tip top shape with a door hinge pin and bushing kit from Eckler's Early Chevy . 1949-1954 Chevy Door Hinge Pin And Bushing Kit .

Buy Now!New Door Hinge Pin & Bushing Kit from 1AAuto.com http://1aau.to/ia/1ADMX00340If the door hinges on your truck are creaking, or the door is sagging, y

I ended up using a vice and a box end wrench as a spacer to pull them thru on the bottom hinge. After getting the bushings installed, the ID shrunk from 0.3435" down to 0.334". This makes it very tight for the pin. This is a good thing, put the hinge back together, and use a hammer to install the pin. It's as tight as anyone could ever hope for.

Step 1: Remove door spring, bushings, and old hinge pins. Remove the retainer clip of the hinge pin on the top using pliers and screwdriver. Wiggle it loose using the screwdriver, grab it and keep hands loose to work using pliers. Remove

5/30 · All of the bolts are easily accessible with a ratchet, except one on the door side of the hinge. This one bolt is obstructed by the roller detent rod or pin. Open the door and remove this one bolt from the opposite, door jam side. Close the door and remove the rest of the bolts and take the hinge off.

Restore the convenience of a properly functioning vehicle door with our Door Hinge Pin and Bushing Kit. It returns a sagging door to proper alignment and operation. Kit includes all necessary hardware for the repair. Durable construction-hardened steel pin and brass bushing. Use the kit to replace only the damaged pin and bushing-instead of the

Put the hinge pin bushing into place Tap the bushing in with a hammer Apply grease to the bushing Push the two parts of the hinge together Push the pins into place in the hinge Put a socket onto the pin Use the vise and socket to push the pin in Put the nuts onto the hinge pins Repeat these steps for the other side of the same hinge

When the pins and bushings get so bad that the bushing is worn out and then the pins are now wearing into the hinge hole itself then this get tricky. if hinge hole is egg shaped the new bushings will not last. the door will hang again in a few weeks. this is where is get costly, the hinges now need replacing. i have gotten good at welding the

Location: East Peoria,IL. Local Time: 3:14 AM. Yes you must remove your doors.Then remove the hinges.Knock the pins out of the hinges.Drill out the holes and insert bushings.Then reassemble the pins on the hinge .Note you must drill the holes the right size or you will ruin the hinge.

Out just use a chisel or a. Screwdriver there we go take the new bushings. And just put them in position might have to tap them down a little bit that one's. Okay. That's good take this bracket.

This kit includes the pins and bushings necessary to repair the upper hinge and lower hinge on one door. Our kits include the parts to repair the upper 

4/23 · 1A Auto shows you how to fix your sagging and sloppy door hinges on your 88 to 98 Chevy or GMC Silverado Sierra Pickup Truck and 92 to 99 Suburban, Yukon ,

With both halves of the hinges in view, you can easily drive out the pins (and bushings if needed). Also note position of pins. Bushings can be 

Place a nail punch on the hinge bolt inside the door. While supporting the door by hand or with your support object, tap the hammer to push the nail punch into 

Storm Door Hinge pin replacement kit. Includes 6 nylon pins, 6 nylon bushings and 3 metal springs. Used in storm door hinges by several manufacturers. Color: White Spring: 1/4 x 2-1/2 inches Bushing: 5/16 /2 Bottom Pin length: 1-3/16 Pin Diameter: 5/16 - 3/16 Priced and Sold as Package.

Starting with the upper hinge, slide the new brass bushings into the hinge. Insert the car door hinge pin into position just as the old hinge 

By purchasing the Dorman door hinge parts, you can easily and conveniently restore the proper function of your vehicle door by using this door hinge pin and bushing kit. The door hinge parts help to fix a sagging or lax door to the correct alignment while still saving money on the car door hinge repair cost. The Bottom Line

This repair should be performed when the existing pins and bushings have worn to the point where the door is sagging when opened. While the vehicle in this video is a Chevy Blazer, S10 the process

Use a hammer to gently tap at first, then hammer more firmly at the end to fully engage the pins in the new bushings. Place your new retainer clips over the bushings and use your small socket or a small hollow piece of tube to hammer the retainer rings in place, ensuring they are fully seated to keep the pins from coming out.

Harbor Freight has the tool for $3.99. I just bought one last Friday and replaced my hinge pins this weekend on my 2000 Chevy Blazer. You have to get that tool. Online they are $15.00.